PERANCANGAN TRAFFIC SPIKES OTOMATIS TYPE SURFACED MOUNTED BERBASIS MICROCONTROLLER ARDUINO UNO DAN SENSOR ID CARD
Abstract
Traffic Spikes are devices or devices used to obstruct or stop the movement of wheeled vehicles by piercing vehicle tires. In this study to meet the requirements for traffic spikes, an arduino uno microcontroler-based automatic traffic spikes control system with identity card (ID Card) sensor was designed. In its design, a Surface-Mounted Traffic Spikes has 8 blades which are used to pierce the tires of the vehicle if the user does not carry out the procedures of using traffic spikes correctly, then the automatic control system reads the tool, the blade stands upright with the position 900 and given a load for testing in the form of a car, and the blade is able to withstand the load as desired, then the tool has been successfully tested. The design of the resulting traffic spikes has dimensions of length of 1000 mm, width of 610 mm, and height of 100 mm. The results of the traffic spikes components are frame design, frame cover design, shaft design, spikes blade design, pillow block design, peg design. The simulation results of the design made are the displacement process has a minimum load consisting of 1000e - 030 mm and an acceptable maximum load of 3,954e - 000 mm, stress has an acceptable minimum load of 1,005e + 003 Nm ¬-2 and pressure the maximum acceptable is 3,411e - 009 and the maximum load is 9.278e-004.
.
Keywords:
Traffic Spikes, Microcontroller Arduino Uno, ID Cards
__________________________
Abstrak
Traffic Spikes adalah perangkat atau alat yang digunakan untuk menghalangi atau menghentikan pergerakan kendaraan roda dengan menusuk ban kendaraan. Dalam penelitian kali ini untuk memenuhi syarat traffic spikes, maka dirancang sistem kendali otomatis traffic spikes berbasis microcontroler arduino uno dengan sensor identity card (ID Card). Dalam perancangannya dibuat sebuah traffic spikes dalam bentuk tanjakan (Surface-Mounted Traffic Spikes) yang memiliki 8 buah pisau yang digunakan untuk menusuk ban kendaraan apabila pengguna tidak menjalankan prosedur pemakaian traffic spikes dengan benar maka alat membaca sistem kendali otomatis, mata pisau berdiri tegak dengan posisi 900 dan diberi beban untuk pengujian yang berupa mobil, dan mata pisau mampu menahan beban seperti yang diinginkan, maka alat dinyatakan telah berhasil pengujiannya. Perancangan traffic spikes yang dihasilkan memiliki dimensi panjang 1000 mm, lebar 610 mm, dan tinggi 100 mm. Hasil rancangan komponen-komponen traffic spikes rancangan rangka, rancang penutup rangka, rancangan poros, rancangan pisau spikes, rancangan pillow block, rancangan pasak. Hasil Simulasi dari rancangan yang dibuat adalah proses dibuat displacement memiliki beban minimal yang terdiri sebesar 1000e – 030 mm dan bebanmaksimal yang dapat diterima sebesar 3.954e – 000 mm, stress memiliki beban minimal yang dapat diterima sebesar 1.005e + 003 N.m¬-2 dan tekanan maksimal yang dapat diterima sebesar 3.411e – 009 dan beban maksimalnya 9.278e-004.
Kata Kunci:
Traffic Spikes, Microcontroller Arduino Uno, ID Card
__________________________
Keywords
Full Text:
PDFReferences
Arifin, M., Hartayu, R., & Elektro, J. T. (2019). Sistem parkir menggunakan kartu rfid 1,2. 1.
Bhansali, S. N. (2015). Development of Mechanism for Road Spike System. 4(07), 665–667.
Franseda, A., Dirgantoro, I. B., & Saputra, R. E. (2017). Implementasi Sistem Kendali Otomatis Pada Pintu Gerbang Parkir Implementation of Automatic Control System for Parking Gate. E-Proceeding of Engineering, 4(1), 835–841.
Handoko, P. (2017). Sistem Kendali Perangkat Elektronika Monolitik Berbasis Arduino Uno R3. November, 1–2.
Lubis, S. (2019). Jurnal Rekayasa Material , Manufaktur dan Energi FT-UMSU Jurnal Rekayasa Material , Manufaktur dan Energi FT-UMSU. 2(1), 44–53.
Mukhtarom, A., Basuki, A., & Aswin, M. (2017). Pemerataan Utilisasi Jaringan Multipath dengan Mode Controller Proactive-Reactive pada Software Defined Networking. 11(2), 60–64.
Mulyani, A. (2018). Perancangan Sensor Jarak Aman Kendaraan Bermotor Menggunakan Mikrokontroler Arduino Uno R3. Jurnal Algoritma, 15(1), 22–28. https://doi.org/10.33364/algoritma/v.15-1.22
Ranjith, M., Sneha, S., Kumar, S. S., Sridharan, R., & Srinath, R. (2017). Fabrication Of Automatic Tyre Killer For Theft Vechicle. 4(1), 17–20.
Ridwan, A., Darjat, & Sudjadi. (2014). Dosen Pada Prototipe Sistem Ruang Kelas Cerdas.
Sidik, M. A. B., Rusli, M. Q. A., Adzis, Z., Buntat, Z., Arief, Y. Z., Shahroom, H., Nawawi, Z., & Jambak, M. I. (2015). Arduino-Uno based mobile data logger with GPS feature. Telkomnika (Telecommunication Computing Electronics and Control), 13(1), 250–259. https://doi.org/10.12928/TELKOMNIKA.v13i1.1300
Syofian, A., & Padang, F. (2016). Pengendalian Pintu Pagar Geser Menggunakan Aplikasi Smartphone Android Dan Mikrokontroler Arduino Melalui Bluetooth. 5(2252), 45–50.
Udenia, S., & Bhati, M. (2014). Traffic Spike System. International Conference on Multidisciplinary Research & Practice, I(Viii), 645–650.
Widyaningrum, F., Jatisukamto, G., & Ilminnafik, N. (2018). Analisis Struktur Statis Provision Crane kapal laut . Material provision crane yang digunakan di dalam penelitian ini adalah structural steel. 11(April), 18–21.
Winerungan, R. Z., Sompie, S. R. U. A., & Pang, D. (2014). Rancang Bangun Alat Identifikasi Pada Pintu Portal Menggunakan Sistem RFID (Radio Frequency Identification). E-Journal Teknik Elektro Dan Komputer, 3(3), 51–58.
Wulandari, R. (2016). Analisis QoS (Quality Of Service) Pada Jaringan Internet (Studi Kasus : Upt Loka Uji Teknik Penambangan Jampang Kulon – LIPI). Jurnal Teknik Informatika Dan Sistem Informasi, 2(2), 162–172. https://doi.org/10.28932/jutisi.v2i2.454
Zulita, L. N. (2016). Perancangan Murottal Otomatis Menggunakan Mikrokontroller Arduino Mega 2560. 12(1), 89–98.
Zulkarnain, D., & Julian, E. S. (2017). Perancangan Sistem Parkir Dengan Rekomendasi Lokasi Parkir. JETri Jurnal Ilmiah Teknik Elektro, 14(2), 17–28.
DOI: https://doi.org/10.38038/vocatech.v2i1.30
Refbacks
- There are currently no refbacks.
VOCATECH : Vocational and Technology Journal
Unit Penelitian dan Pengabdian Masyarakat & Penjaminan Mutu
Akademi Komunitas Negeri Aceh Barat
Komplek STTU Alue Peunyareng, Ujong Tanoh Darat, Meureubo, Kabupaten Aceh Barat, Aceh 23615
Telp. (0655) 7110271
Email: vocatech@aknacehbarat.ac.id
VOCATECH: Vocational Education and Technology Journal Published by:
Unit Penelitian dan Pengabdian Masyarakat & Penjaminan Mutu
Akademi Komunitas Negeri Aceh Barat
Indexed by:
VOCATECH: Vocational Education and Technology Journal Creative Commons Attribution-ShareAlike 4.0 International License.